Hi, I currently have a c5402 booting via serial (code & data loaded from the serial port), however i have now moved to the...

Hi, I currently have a c5402 booting via serial (code & data loaded from the serial port), however i have now moved to the c6415 and am looking to boot the processor via a pci interface. Does anyone have any information on the best process to achieve this ? Th

Hi. Is anyone familiar with booting an application from FLASH? I have followed very carefully what the folks at TI have suggested. ...

Hi. Is anyone familiar with booting an application from FLASH? I have followed very carefully what the folks at TI have suggested. Obviously and expectedly, it did not work. I have also tried everything under the sun I thought was reasonable but to no avail. I am now convinced that t

Hello, I?m having problem in booting DM6446 board. Please check out the snapshots. Waiting for valuable...

Hello, I?m having problem in booting DM6446 board. Please check out the snapshots. Waiting for valuable suggestions??.. Thanks Priya??? DISCLAIMER: ------------------------------------------------------------------------------------------------ ----------------------- The contents of this e-mail and any attachment(s) are confidential and intended for the named reci

Hi We have TMS320TCI6488 Mezanine ACM EVM board. How to load image through ethernet ? Any configuration setting file or docs on EMAC...

Hi We have TMS320TCI6488 Mezanine ACM EVM board. How to load image through ethernet ? Any configuration setting file or docs on EMAC booting?. Raviraj _____________________________________

Hi ALL:) I have problem in booting the c672x device through I2C and SPI both in SLAVE` n MASTER mode.And, I would like to known about the...

Hi ALL:) I have problem in booting the c672x device through I2C and SPI both in SLAVE` n MASTER mode.And, I would like to known about the TMS320C672X DSP`S I2C SPI BOOT timing infomation.For example,the I2C MASTER mode useing a START-SLA&write-ACK-8bitADDR-ACK-8bitADDR-ACK-Sr - SLA&read-ACK-8bit DATA-ACK-8bitDATA-NACK-stop sequence. and what about the others? Mainly I`d like to know what tim...

Hi, They simply increased number of wait states from 6 to 8. With best regards, Taras _____ From: Jeff Brower...

Hi, They simply increased number of wait states from 6 to 8. With best regards, Taras _____ From: Jeff Brower [mailto:j...@signalogic.com] Sent: Saturday, April 26, 2008 12:57 AM To: Kurnytskyi Taras Cc: c...@yahoogroups.com Subject: Re: [c6x] HPI booting problem Kurnytskyi- Thank you for the help. Finally, the problem with HPI is solved. Well, since my last mail regar...

Hello, I am looking for help about booting problems in a C6414 DSP. I make the configuration for the DSP to boot on the EMIFB bus reading...

Hello, I am looking for help about booting problems in a C6414 DSP. I make the configuration for the DSP to boot on the EMIFB bus reading the first 1kB of my Flash. But when I check the signal on the /BCE1 pin it is remaining high instead of going low to start reading the flash (what should be done automatically by the chip explain the datasheet of the DSP). I already verify my c

HAI GUYS IAM USING C6202 AND CCS1.2 FOR MY APPLICATION. I FLASHED MY APPLICATION, IT WLL BOOT WELL AND WORKS FINE WHEN U...

HAI GUYS IAM USING C6202 AND CCS1.2 FOR MY APPLICATION. I FLASHED MY APPLICATION, IT WLL BOOT WELL AND WORKS FINE WHEN U CONNECT JTAG AND RUN, IF U REMOVE JTAG AND RESET THE BOARD IT WON'T WORK. THERE IS NO PROBLEM IN RESET AND BOOTING PROCEDURE........ , any idea?

hello friends iam using c6211 dsk and ccs V2.0. in my application i need to control user led's(IO_port)in c6211 dsk board. ...

hello friends iam using c6211 dsk and ccs V2.0. in my application i need to control user led's(IO_port)in c6211 dsk board. ,it working fine,my problem is after booting from flash i need to modify EMIF CE1 register to 32 bit asyncrounus mode to access IO port. if wr

ROM   -BOOTING     TMS320C6211 DSP   is a single   map device with on chi

ROM   -BOOTING     TMS320C6211 DSP   is a single   map device with on chi

Hi Jeff, Thank you for the help. Finally, the problem with HPI is solved. Well, since my last mail regarding the problem dates around 2 months...

Hi Jeff, Thank you for the help. Finally, the problem with HPI is solved. Well, since my last mail regarding the problem dates around 2 months back does not mean all this time was spent for finding solution:-). Just on the contrary, the problem solving took less than the day. Since they were my colleagues who made hardware job, set timings, etc. I decided it would be reasonable to ask them...

Hi All, Is it resonable to be able to run a bootloader that recives data via the MCBSP, copies that data into external ram and then...

Hi All, Is it resonable to be able to run a bootloader that recives data via the MCBSP, copies that data into external ram and then runs it? Would I have to process the .out file in any way or can I just load the whole file? Does anyone understand what I'm trying to do and can fill in the gaps? or point me at a similar example?

Well, I have a production version of my code compiling and linking, but it doesn't run when I load it across the PCI bus although it does run if...

Well, I have a production version of my code compiling and linking, but it doesn't run when I load it across the PCI bus although it does run if I load it via Code Composer. The DSP is a 320C6416 and it is a Spectrum Digital development board. I have set the DIP switches on that board for a PCI boot, and Bit 2 of the HDCR register is being set, which indicates the DSP recognizes that i...

Hello again, Some other results of HPI boot testing. The same small DSP bootloader, which at boot is written to address 0, now is written in...

Hello again, Some other results of HPI boot testing. The same small DSP bootloader, which at boot is written to address 0, now is written in SDRAM buffer during normal application running. And results are as follows: while during the boot several words are corrupted, during simple write in SDRAM memory it is completely OK! No corrupted words. What could it be during boot that makes things w...

Hello all, I'm working on the project whose objectives are 1) to establish communication via HPI between Atmel's At91M40008 host processor...

Hello all, I'm working on the project whose objectives are 1) to establish communication via HPI between Atmel's At91M40008 host processor and C6711D and 2) to boot DSP processor via HPI. I've already tested communication and it works satisfactory but not ideally. Not ideally because I have to read only in autoincrement mode since read in fixed mode is unstable and thus incorrect in g...

I want to burn my program of 896K size (.out) file into flash using "FLASH BURN UTILITY on EVMDM642 , when i burn it the "FPGA Code" overrrite...

I want to burn my program of 896K size (.out) file into flash using "FLASH BURN UTILITY on EVMDM642 , when i burn it the "FPGA Code" overrrite through it, so kindly suggest me what i have to do.

HI! All  I am working on DM642 , with CCS 3.0.0.21 I am converting *.out file to*.bin, and burning this bin into flash. If I reset...

HI! All  I am working on DM642 , with CCS 3.0.0.21 I am converting *.out file to*.bin, and burning this bin into flash. If I reset the  board after sucessfull completion of flash burning , the board gets booted from flash for 1 or 2 time , but if I try to reset it many times it is not booting up from flash. Can any body through some light on it. I h

Hi Guys, I have 6713 DSK attached with ADC which is sampling signal with maximum frequency 150 kHz then computing FFT. I burn all the codes to...

Hi Guys, I have 6713 DSK attached with ADC which is sampling signal with maximum frequency 150 kHz then computing FFT. I burn all the codes to boot from Flash and it is working quite fine. After FFT I am writing FFT values to Flash memory. For some reason, I am not getting the correct FFT peak from the values saved in Flash. I am sampling 10 kHz signal and the peak shows as it was 50 kHz sign...

Hi, Using DM642 on custom hardware, all hardware has been tested and verified (External SDRAM/FLASH etc). I have a program that...

Hi, Using DM642 on custom hardware, all hardware has been tested and verified (External SDRAM/FLASH etc). I have a program that runs correctly when loaded via JTAG into RAM and executed in CCS. However when the program is loaded from FLASH (via CE0 boot selection) it does not execute the same. I know the GEL file in CCS helps setup the

hai friends, i wish to boot my appliction from flah memory , my intention is to make work the particular application written in flash , when...

hai friends, i wish to boot my appliction from flah memory , my intention is to make work the particular application written in flash , when the supply is given and reset the processor. how can i do this , as the default boot mode is from flash, i hope that i need only to save the program in flash by specifing in the location in .Cmd file. if i am wrong then what the way to do this? -- ...