Hi, For my new design I am planning to make DM642 as PCI system host. The system will consist of DM642 and USB controller with PCI...

Hi, For my new design I am planning to make DM642 as PCI system host. The system will consist of DM642 and USB controller with PCI interface. As there is no other processor required on board, I want to make DM642 as PCI system host. I have gone thru the datasheet and found out that DM642 does not generate IDSEL and it does not have PCI arbitra

Dear all, I want to capture the images using a camera and have to display it on a monitor/TV using dm642 EVM board. My idea to proceed with...

Dear all, I want to capture the images using a camera and have to display it on a monitor/TV using dm642 EVM board. My idea to proceed with this is like below: connect the camera and configure one of the Decoder of dm642(dm642 has 2 decoders). I can choose and configure DM642 using I2C module. The output of the decode will be 4:2:2 YCbCr format. This is given to the video p

Hi all, i am running audio/video on DM642 and ARM processor. when i am running audio/video combine on DM642 only the quality of both real...

Hi all, i am running audio/video on DM642 and ARM processor. when i am running audio/video combine on DM642 only the quality of both real time audio/video is good but when i am using HOST PORT INTERFACE(hpi) to communicate between DM642 and ARM9 and then running real time audio/video on that there is degradation in real time audio quality.I have the f

Hello We've successfully built a board based on DM642 and we've interfaced an SDRAM DIMM module to DM642 over EMIF (MTYPE: 64 bit SDRAM). Has...

Hello We've successfully built a board based on DM642 and we've interfaced an SDRAM DIMM module to DM642 over EMIF (MTYPE: 64 bit SDRAM). Has anyone tried this before. I'd like to know if there's any performance hit in using SDRAM DIMM modules versus using a standard SDRAM chips. If yes, how much. We're running DM642 at 600 MHz & SDRAM is configured at 100 MHz. Thanx & regards Gaut

Hi All, I have read the documents about PCI in the folders of the DM642 in the TI site. But I found some troubles to understand what I should...

Hi All, I have read the documents about PCI in the folders of the DM642 in the TI site. But I found some troubles to understand what I should do for configure the DM642 as a slave and I would like to do some questions: If, the DM642 is a slave, the task of the configuring the registers is make by the master? What are the registers that I (SLAVE) have to configure? Tank you for yours...

Hi: I'm writing a linux driver for C64(board dm642).In order start DM642 in linux host,I do things as follow: 1)warm reset c64 2)init emif...

Hi: I'm writing a linux driver for C64(board dm642).In order start DM642 in linux host,I do things as follow: 1)warm reset c64 2)init emif for dm642 3)mmap the c64's iram to userspace 4)set c64's memory zero 5)load c64's bin file to iram 6)trigger dspint to start c64 BUT,i doesn't work.When i clear the c64's iram, the whole system is crashed. I find that C64 is not in pci boot mod...

Just wondering about a design I recently saw which had a DM642 interfaced to SDRAM using a 32-bit wide data bus. The SDRAM chip only has a 32-bit...

Just wondering about a design I recently saw which had a DM642 interfaced to SDRAM using a 32-bit wide data bus. The SDRAM chip only has a 32-bit wide bus and the other 32 bits of the DM642 are not used. Not sure why it was designed this way as it only going to slow down the EMIF that much more. Can this design work? Is this going to be problem? Any special commands required on the DM642 to s...

Hello I have a small project using DM642, 'video streaming using DM642' I am new in this field, what i want to do is to capture a video ,...

Hello I have a small project using DM642, 'video streaming using DM642' I am new in this field, what i want to do is to capture a video , then stream that video using DM642 EVM anyone of you has any idea or resource on this please help me thanks in advance -- Ahmed

Dear Experts, ? 1. We recently acquired a DM642 Evaluation board through TI. Alongwith the Board, we received an installation of CCS 2.2...

Dear Experts, ? 1. We recently acquired a DM642 Evaluation board through TI. Alongwith the Board, we received an installation of CCS 2.2 and the DM642 EVM CD. However, the DM642 EVM documentation mentions that the device drivers & emulator drivers in the CD will work only with CCS v3.0 or higher. Kindly confirm whether this is true. ? 2. Sti

Hi Anand, I am Prafull and currently working on DM642 in the company situated in Pune.Though i m also a newbee in this, I d be glad if i cld...

Hi Anand, I am Prafull and currently working on DM642 in the company situated in Pune.Though i m also a newbee in this, I d be glad if i cld help u in any regard. Here is my mobile no. 9860611844. mail id : p...@yahoo.com Pls feel free to call or mail me Thanks & Regards Prafull > Hi Experts, > > My name is Anand and I am a rookie in DM642 development. I would like > to know

Hi All, We are doing a project using DM642 processor. In our application we want to store the video data into the HARD DISK of windows XP PC...

Hi All, We are doing a project using DM642 processor. In our application we want to store the video data into the HARD DISK of windows XP PC through the PCI of DM642. My question is: 1.Will the video data trasferred directly or wil that be converted to some other form as it has to use PCI? 2.What wil be the interface IDE or SCSI? 3.Will the transfer be serial or parallel? Please clarify my ...

Dear All, I am Nilanjan. I am very new to this group. I need to port a HEAAC decoder on Dm642 hardware. Can you guys tell what will be current...

Dear All, I am Nilanjan. I am very new to this group. I need to port a HEAAC decoder on Dm642 hardware. Can you guys tell what will be current market standard MCPS figure for HEAAC decoder(fixed point version) on DM642. And I also need some information which are the areas I should look first for HEAAC decoder optiomization on the board. I am highly looking forward to yuor reply. Thanking you...

Hello, I'm using DM642 to process video. However, I found that the frames were captured as YUV422 format by the chip on my DM642...

Hello, I'm using DM642 to process video. However, I found that the frames were captured as YUV422 format by the chip on my DM642 EVM. Then the frames were transformed to be RGB565 format and put into an output buffer. I now utilize the image data in the output buffer to perform desired image processes based on RGB color model. I wonder if the flow is appropriate? Or I'm supposed...

Hi, all Recently, I develop Mpeg4 decoder by using DM642. Video bitstream was transfered from PC throuth PCI to SSDRAM in dm642. The bitstream...

Hi, all Recently, I develop Mpeg4 decoder by using DM642. Video bitstream was transfered from PC throuth PCI to SSDRAM in dm642. The bitstream was a ".avi" file and is of PAL type video. The frame is of 352*288 pixels(CIF type). As we know, to correctly display the video, the output frames should be in speed of 25 frames per second. While the frame rate is a little faster than 25 frames per s...

Hi all: Recently, i want to develop a 4 channel video data's compression with 4 channel audio data's compression based on dm642, while i...

Hi all: Recently, i want to develop a 4 channel video data's compression with 4 channel audio data's compression based on dm642, while i found that some pins of the input port of the dm642 chip's video and audio is the same. what can i do to realise the video and audio uninterfere each other ? thanks in advance !

Hi All, We have a DM640-based custom board with CPU operating at 400MHz. This board was working fine. Now we have replaced the DM640...

Hi All, We have a DM640-based custom board with CPU operating at 400MHz. This board was working fine. Now we have replaced the DM640 with DM642-720 chip. The input PLL clock is same, i.e. input PLL clock is 33MHz and DM642 CPU is also running at 400MHz. Is this fine? We are trying to access SDRAM using the same GEL file as used for DM640 board. Since we have not changed any cloc...

hi iam new in dsp processor. i have board dm642 evm.i want implement bilinear interpolation on dm642 evm.when i run the program on board, video...

hi iam new in dsp processor. i have board dm642 evm.i want implement bilinear interpolation on dm642 evm.when i run the program on board, video output has many delay & my video is not real time. plaese help me about this problem. what i must doing for real time bilinear interpolation. for this purpose ido thie steps: first i put frame of video in SDRAM then processing them.finally put them ...

hello my question is how to control the dc_port's pins of dm642 when sending data.(Note: these pins are connected to the video port(vp1,2,3 )...

hello my question is how to control the dc_port's pins of dm642 when sending data.(Note: these pins are connected to the video port(vp1,2,3 ) of dm642). how can I achieve this task? please I'm jammed and I need your help. thank you _____________________________________

Dear group, to anyone who has used DM642 on a PCI card and accessed it from a Windows PC using dm642_lib (from ValleyTech, part of EVM642...

Dear group, to anyone who has used DM642 on a PCI card and accessed it from a Windows PC using dm642_lib (from ValleyTech, part of EVM642 board): Did you use dm642_lib in a multithread environment? If yes - how? In my application, the DM642-access is implemented in a Win32-dll. Several Windows application use this dll to access the DM642 in parallel. I implemented ressource protection (M...

Hi All, I am operating the video port in 8 bit RAW capture mode on DM642. I have used TW2816 Techwell video decoder which is interfaced to...

Hi All, I am operating the video port in 8 bit RAW capture mode on DM642. I have used TW2816 Techwell video decoder which is interfaced to video port of DM642. I was able to capture the video, but the video is not synchronized this is due to the lack of sync signals from TW2816. So i have pulled the CAPEN signal as high(VPCTL0 is connected to VCC), so the video port captures the data contionous...