DSPRelated.com

z-plane representation of single order all-pass filter

Started by "fau...@yahoo.com [audiodsp]" in Audio Signal Processing10 years ago 1 reply

I'm used to the s-plane representation of an all-pass filter, where the pole(s) are on the left-side of the y-axis, and the zeroes are mirror...

I'm used to the s-plane representation of an all-pass filter, where the pole(s) are on the left-side of the y-axis, and the zeroes are mirror imaged across the y-axis. It's fairly clear that as omega increases (increasing frequency) in s = j * omega, that the length of the vectors that go from the y-axis to the mirror imaged poles and zeroes will be the same length (per pole-zero pair). Howeve...


Filtering out dither noise from 63Hz sine wave

Started by "sen...@yahoo.co.za [audiodsp]" in Audio Signal Processing10 years ago 1 reply

I have 24 bit ADC data with dithering noise on it. My original signals into the ADC were quite small. The dithering noise therefore makes out a...

I have 24 bit ADC data with dithering noise on it. My original signals into the ADC were quite small. The dithering noise therefore makes out a large part of the amplitude of the ADC data. I want to remove the noise to recover as much as possible of the actual signals. I find lots of websites that say that the dithering noise can be filtered out but no description of how this can be done. Unfortu...


ref: pg 174, Oppenheim, Schafer and Buck, Discrete-Time Signal Processing, second ed.

Started by "Kri...@yahoo.co.in [audiodsp]" in Audio Signal Processing11 years ago

Subj= ect: =CE=B4(=CF=89/ T) =3D T.=CE=B4(=CF=89)=20=20=20=20=20 I'm...

Subj= ect: =CE=B4(=CF=89/ T) =3D T.=CE=B4(=CF=89)=20=20=20=20=20 I'm sorry that this email turned out long. My apologies that I couldn't fig= ure out my exact question. So only managed to disperse all the information = I could that hopefully revolves around it.=20=20=20=20=20=20 To start with, I wish to understand the dif...


SPL computation, Prms computation

Started by wmta...@dcs.upd.edu.ph in Audio Signal Processing11 years ago

Hi I have a microphone(with preamp) connected to a microcontroller - I am able to get samples now, which could be converted to pressure since I...

Hi I have a microphone(with preamp) connected to a microcontroller - I am able to get samples now, which could be converted to pressure since I have the sensitivity of the microphone. I want to get the sound pressure level. According to "Engineering Acoustics" and "Engineering Noise Control"(Bies and Hansen), which was referenced by Wikipedia as well http://en.wikipedia.org/wiki/Sound_pressure...


Spectral envelope normalization (speech processing)

Started by kout...@hotmail.com in Audio Signal Processing11 years ago

Dear forum, I created a synthetic speech signal x[n] of 256 samples assuming that the source signal u[n] is an impulse train (not a glottal...

Dear forum, I created a synthetic speech signal x[n] of 256 samples assuming that the source signal u[n] is an impulse train (not a glottal flow signal) and also I assumed that there are no lips. The vocal tract filter h[n] is an all pole filter of order 10. So, in frequency domain we have X(w)=H(W)U(W). I computed with the modified periodogram the PSD of X(w) and with freqz the PSD of H(w) ...


Sampling Rate Conversion

Started by prat...@gmail.com in Audio Signal Processing11 years ago 1 reply

Hi experts, I want to convert audio sampled at 192KHz to 44.1kHz. It involves interpolation by 147 and decimation by 640....

Hi experts, I want to convert audio sampled at 192KHz to 44.1kHz. It involves interpolation by 147 and decimation by 640. I'm designing filter coefficients using fda tool, with FIR equiripple method. The parameters I gave are fs - 192000*147 fpass - 16000 fstop - 22050 Apass = 0.4 Astop = -80dB But the fda tool gets hanged after some time. Is there any alternative...


Request for Guidance on Optimal DSP for Audio Application

Started by rich...@btinternet.com in Audio Signal Processing11 years ago

Hi, I am designing an audio DAC and my intention is to use a DSP to interface with the CD player to receive the optical or coaxial signal. I...

Hi, I am designing an audio DAC and my intention is to use a DSP to interface with the CD player to receive the optical or coaxial signal. I have been examining the Elektor series from 2011 on using the Freescale DSP 56000 series devices. The capability I wish to implement is as follows : 1. Accept the I2S input signal. 2. Implement a circuit that allows the DSP to be programmed whilst in s...


Strumming problem.

Started by exactlybest in Audio Signal Processing11 years ago 2 replies

Hi. I have a very accurate frequency detector that works pretty much perfectly with my guitar. I want to implement certain features that...

Hi. I have a very accurate frequency detector that works pretty much perfectly with my guitar. I want to implement certain features that involve note validity (user plays a note program displays-> checks for validity) my exact problem in an example can be explained like this: if i strum open E (82hz) once and my program demands an open E followed by an open E it will count both of these no


fftw problem

Started by bauzane in Audio Signal Processing11 years ago 1 reply

I'm an Italian university student. I'm trying to use FFTW libraries. I have problems but I don't know in which forum I may ask help so I try here....

I'm an Italian university student. I'm trying to use FFTW libraries. I have problems but I don't know in which forum I may ask help so I try here. I wrote the following C program #include #include #include #include void main() { int i; int N, num_points; // dimensione trasformata double T; double *in; // puntatore dati in ingresso alla FFT


2nd vs 1st order all pass filter

Started by bw...@nchsoftware.com in Audio Signal Processing12 years ago 1 reply

Given that the magnitude response of a first order all pass filter is perfectly flat, what reasons are there to consider a filter greater than one...

Given that the magnitude response of a first order all pass filter is perfectly flat, what reasons are there to consider a filter greater than one order? Presumably it is to do with varying the phase in a different way, but can anyone give me a good real world application?


Ask a Question to the DSPRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright