DSPRelated.com
Forums

C6416 IEK with CCS 2.20 and XDS560

Started by KAnand August 1, 2003
Hello all:

I am having trouble with obtaining the correct
configuration for this
setup:

1. ATEME's IEKC64 with C6416 Dsp, Silicon Rev 1.03
2. Code Composer Studio 2.2
3. XDS560 Emulator

I did not have to use the emulator's drivers since
there is a driver that comes with CCS 2.2. My problem
is, after a complete install and restart, I do not see
my configuration in the "Available configuration" tab
of CCS Setup and there dont seem to be any .dvr files
that I can import to get this one on. The right
configuration I am supposed to use for my setup is:

"C6414,15,16 Rev 1.0x XDS560 Emulator" - and this
doesnt appear. The closest I see is "C64xx Rev 1.0
XDS560 Emulator".

Could someone tell me if which update I need to get
the CCS Setup right ? I did contact TI a few times but
didn't find an answer. I am also attaching a
screenshot of the correct setup that I found (luckily)
from TI.

Any help would be really appreciated,

Thanks in advance,
Anand

__________________________________

Attachment (not stored)
AvblConfig.jpg
Type: image/pjpeg



Thanks for your help. I figured that the required update was: 2.20.18

However, it would be nice if someone could tell me how to choose the
Clock (TCLK) in the "Board Properties" tab of CCS Setup tool. I
chose "User Defined" and left the value at 1, ("Automatic" will not
start up CCS) and then the system is really slow. For e.g. file write
onto host disk from the IEK is happening at like 2 KB / sec; Im sure
the XDS560 can run faster than that :) !

Thanks in advance for any help.

Regards
Anand

--- In , KAnand <akalya@y...> wrote:
> Hello all:
>
> I am having trouble with obtaining the correct
> configuration for this
> setup:
>
> 1. ATEME's IEKC64 with C6416 Dsp, Silicon Rev 1.03
> 2. Code Composer Studio 2.2
> 3. XDS560 Emulator
>
> I did not have to use the emulator's drivers since
> there is a driver that comes with CCS 2.2. My problem
> is, after a complete install and restart, I do not see
> my configuration in the "Available configuration" tab
> of CCS Setup and there dont seem to be any .dvr files
> that I can import to get this one on. The right
> configuration I am supposed to use for my setup is:
>




Anand,
 
I am sure that was s-l-o-w.  You must use a user defined TCLK value for 1.0x devices.  I believe that the value that you enter in is 2x the desired clock rate.  Ti's default configuration used 10 mhz [I cranked mine to 20 mhz and had no problems].
 
mikedunn

Anand K <a...@yahoo.com> wrote:

Thanks for your help. I figured that the required update was: 2.20.18

However, it would be nice if someone could tell me how to choose the
Clock (TCLK) in the "Board Properties" tab of CCS Setup tool. I
chose "User Defined" and left the value at 1, ("Automatic" will not
start up CCS) and then the system is really slow. For e.g. file write
onto host disk from the IEK is happening at like 2 KB / sec; Im sure
the XDS560 can run faster than that :) !

Thanks in advance for any help.

Regards
Anand

--- In c...@yahoogroups.com, KAnand wrote:
> Hello all:
>
> I am having trouble with obtaining the correct
> configuration for this
> setup:
>
> 1. ATEME's IEKC64 with C6416 Dsp, Silicon Rev 1.03
> 2. Code Composer Studio 2.2
> 3. XDS560 Emulator
>
> I did not have to use the emulator's drivers since
> there is a driver that comes with CCS 2.2. My problem
> is, after a complete install and restart, I do not see
> my configuration in the "Available configuration" tab
> of CCS Setup and there dont seem to be any .dvr files
> that I can import to get this one on. The right
> configuration I am supposed to use for my setup is:_____________________________________
Note: If you do a simple "reply" with your email client, only the author of this message will receive your answer. You need to do a "reply all" if you want your answer to be distributed to the entire group.

_____________________________________
About this discussion group:

To Join: Send an email to c...@yahoogroups.com

To Post: Send an email to c...@yahoogroups.com

To Leave: Send an email to c...@yahoogroups.com

Archives: http://www.yahoogroups.com/group/c6x

Other Groups: http://www.dsprelated.com