|
Hello all, I have ccs 2.0 and Emulator drivers from Spectrum Digital. I have connected the Emulator (XDS510PP PLUS) to my own hardware board(cantains single C6211 processor) and I have configured the ccs in emulator mode. But I am encountering the following problems- When I Configure Using 'Setup CCS 2' and launch the application I am getting the following error. 1. " Trouble Reading CPU Memory: Timeout on Target Processor Please Check Cabling or Multiprocessor Configuration " (Emulator LED is ON) When I cancel this message CCS window opens then I am able to open a project and build it. But When I try to load the .out file on to target, I am getting the following message and I am not able to do it. 2. " Target Endianness doesn't match, Check the Build options or Setup Utility" i don't know what to do at this point. and one more thing, when I launch CCS again I am getting the following error: 3. "Can't Initialize Target CPU" But when I open the SDconfig Utility and reset the emulator and again launch the CCS, I am getting the first error(1). I have checked the Parallel port, Power supplies and cabling. Everything Looks to be very fine. All these things I have tested under : Win98 ,128MB RAM, Pentium3, 866Mhz. Looking forward to Your Solutions...... Simha |
|
|
Target Initialization Problems.........
Started by ●March 12, 2002
Reply by ●March 12, 20022002-03-12
|
Hi Simha, it seems that TI CCS V2.0 have problems with third party boards, because I do also experience the same problem. I'm using a c6701 board from Innovative Integration. What I do is first load a very simple application thru a small terminal applet, which comes with the package. And then open CCS and load my application to the board. Do not reset from CCS, if you want to load a different version of your application just use reload. It does not load a different application however. As for the second problem, check build options of your code, there just switch the endiannes. Hope this helps. Faysal, ------------------- >Hello all, > >I have ccs 2.0 and Emulator drivers from Spectrum >Digital. >I have connected the Emulator (XDS510PP PLUS) to my >own hardware >board(cantains single C6211 processor) and I have >configured the >ccs in emulator mode. But I am encountering the >following problems- > > When I Configure Using 'Setup CCS 2' and launch the >application >I am getting the following error. > >1. " Trouble Reading CPU Memory: Timeout on Target >Processor > Please Check Cabling or Multiprocessor >Configuration " >(Emulator LED is ON) > >When I cancel this message CCS window opens then I am >able to open >a project and build it. But When I try to load the >.out file on to >target, I am getting the following message and I am >not able to do it. > >2. " Target Endianness doesn't match, Check the Build >options or Setup > Utility" > >i don't know what to do at this point. > >and one more thing, when I launch CCS again I am >getting the >following error: >3. "Can't Initialize Target CPU" > > But when I open the SDconfig Utility and reset the >emulator >and again launch the CCS, I am getting the first >error(1). > >I have checked the Parallel port, Power supplies and >cabling. >Everything Looks to be very fine. > >All these things I have tested under : >Win98 ,128MB RAM, Pentium3, 866Mhz. > >Looking forward to Your Solutions...... > >Simha >_____________________________________ >Note: If you do a simple "reply" with your email client, only the author of this message will receive your answer. You need to do a "reply all" if you want your answer to be distributed to the entire group. > >_____________________________________ >About this discussion group: > >To Join: Send an email to > >To Post: Send an email to > >To Leave: Send an email to > >Archives: http://www.yahoogroups.com/group/c6x > >Other Groups: http://www.dsprelated.com >">http://docs.yahoo.com/info/terms/ > > Faysal Basci METU EEE Dept. |
