Hi All,
Our board(Product) has TCI6488 processor. We have a blackhawk JTAG emulator. we
have installed the CCS V3.3 with SR12 patch and installed the JTAG driver. While
we are trying to open the emulator debugger and tried to connect to the target
it shows the below error message.
Error connecting to the target:
Error 0x80002240/-183
Fatal Error during: Initialization, OCS, Control,
This error was generated by TI's USCIF driver.
SC_ERR_CTL_CBL_BREAK_FAR <-183>
The controller has detected a cable break far-from itself.
The user must connect the cable/pod to the target.
Board Name: Blackhawk USB560bp - TCI6488 Emulator
Cpu Name: ICEPICK_C_0
Abort: Close Code Composer Studio.
Retry: Try to connect to the target again.
Cancel: Remain disconnected from the target
Diagnostic: Run diagnostic utility.
Can any one help or have any suggestion?
Thanks in advance,
-Jeeva
_____________________________________
TCI6488 JTAG emulation conection problem.
Started by ●July 31, 2010
Reply by ●August 2, 20102010-08-02
Jeeva,
On Sat, Jul 31, 2010 at 2:23 AM, wrote:
> Hi All,
>
> Our board(Product) has TCI6488 processor. We have a blackhawk JTAG
> emulator. we have installed the CCS V3.3 with SR12 patch and installed the
> JTAG driver. While we are trying to open the emulator debugger and tried to
> connect to the target it shows the below error message.
>
> Error connecting to the target:
> Error 0x80002240/-183
> Fatal Error during: Initialization, OCS, Control,
> This error was generated by TI's USCIF driver.
>
> SC_ERR_CTL_CBL_BREAK_FAR <-183>
> The controller has detected a cable break far-from itself.
> The user must connect the cable/pod to the target.
>
This error means that the target board is not detected.
All that is needed is for the JTAG connector to have ground and presence
detect voltage. [assuming that the emulator address is correct]
mikedunn
>
> Board Name: Blackhawk USB560bp - TCI6488 Emulator
> Cpu Name: ICEPICK_C_0
>
> Abort: Close Code Composer Studio.
> Retry: Try to connect to the target again.
> Cancel: Remain disconnected from the target
> Diagnostic: Run diagnostic utility.
>
> Can any one help or have any suggestion?
>
> Thanks in advance,
>
> -Jeeva
>
>
--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
On Sat, Jul 31, 2010 at 2:23 AM, wrote:
> Hi All,
>
> Our board(Product) has TCI6488 processor. We have a blackhawk JTAG
> emulator. we have installed the CCS V3.3 with SR12 patch and installed the
> JTAG driver. While we are trying to open the emulator debugger and tried to
> connect to the target it shows the below error message.
>
> Error connecting to the target:
> Error 0x80002240/-183
> Fatal Error during: Initialization, OCS, Control,
> This error was generated by TI's USCIF driver.
>
> SC_ERR_CTL_CBL_BREAK_FAR <-183>
> The controller has detected a cable break far-from itself.
> The user must connect the cable/pod to the target.
>
This error means that the target board is not detected.
All that is needed is for the JTAG connector to have ground and presence
detect voltage. [assuming that the emulator address is correct]
mikedunn
>
> Board Name: Blackhawk USB560bp - TCI6488 Emulator
> Cpu Name: ICEPICK_C_0
>
> Abort: Close Code Composer Studio.
> Retry: Try to connect to the target again.
> Cancel: Remain disconnected from the target
> Diagnostic: Run diagnostic utility.
>
> Can any one help or have any suggestion?
>
> Thanks in advance,
>
> -Jeeva
>
>
--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php